Injectable Steroids Recipes Make Equipoise / EQ / Boldenone
Equipoise (boldenone undecylenate) is historically a veterinary
steroid but for some time has been available as an UGL human
preparation as well.
Presently, for the most part there is little specific reason to use
Equipoise in an anabolic steroid cycle. There is nothing that it
does anabolically that Masteron, Primobolan, Deca, or trenbolone
will not do. In terms of side effects, likewise it has no advantage
over Masteron or Primobolan, unless one desires the occasional side
effect of increased appetite, or the side effect of its moderate
conversion to estrogen.
Product Name: Equipoise, EQ (Boldenone Undecylenate)
Appearance: slightly yellow oily liquid
EINECS No.: 236-024-5
|Appearance||Slight yellow oily liquid||Complies|
|Solubility||almost insoluble in water, soluble in vegetable oil.||Complies|
|Specific Rotation||+28° ~ +35°||+33.7°|
|Volatile Impurities||NMT 0.5%||0.2%|
|Water Content||NMT 0.5%||0.21%|
|Residue On Ignition||NMT 0.1%||0.08%|
|Related Substance||NMT 3.0%||Complies|
|Free acid||NMT 0.5%||0.16%|
|Heavy Metals||NMT 10ppm||Complies|
|Endotoxin Bacterium||Not detectable||Not detected|
|Conclusion||Conforms with standard in-house for export|
How to Make Equipoise 200mg per ml
1. 10g Boldenone Undeclynate Powder
7.5ml of Benzyl Benzoate
2.5ml of Benzyl Alcohol
32ml of your favourite Oil
2 18ga needles, 1 25ga Needle
.45 Sterile Whatman Filter
50ml Sterile Vial
Rubbing Alchol/Paper Towels
2. Now that all materials are in place, take out scale, and put on
unsterile 50ml vial on scale and zero out.
3. Draw up 12ml of EQ using 12ml syringe, make sure there are no
airbubbles and plunger is exactly in line with 12ml hatch mark. Now
slowly squirt EQ into vial until scale says 10.0 grams. For me this
is usually exactly 10ml so 1g has 1 mL displacement. Also add the
7.5ml of BB and 2.5ml of BA
4. Now add 30 of the 32ml of oil into the vial to make total volume
of oil/BA/BB/hormone to be 50 mL. Leave the 2ml of oil in syringe
for later use. Put rubber stopper into vial as well as one of the
18ga needles. Boil a pot of hot water and then remove from heat and
put vial into pot for 10 minutes, take out after 5 to shake and put
5. I have a crimper so as to crimp another seal on the vial but you
could also duct tape it on so that rubber stopper doesn't come out
when it is upside down. Here's what it looks like unfiltered but
6. Now take out sterile 50ml vial and wipe stopper with rubbing
alchol. Put 18ga needle and 25ga needle through stopper, and attach
whatman filter to the 18ga needle stuck in vial.
7. Once you've filtered all 50ml and vial is totally empty, take
the last 2ml you had saved and run it through the filter to get all
gear out of it and only leave plain oil in the filter. This is what
final product will look like. Notice I left 25ga pin in.
8. Now put vial in oven at 200 degrees F, and bake for 15 minutes.
Some repeat this step more than once but i never have and not had a
problem. There you go, save yourself a ton of cash and MAKE YOUR
Professional Manufacture: We are genuine and legit pharmaceutical manufacturer, all products
are produced under GMP conditions according to Standard Operation
Procedure(SOP), not from little underground labs or black markets,
so the quality is guaranteed.
- 100% customs pass guaranteed.
- High quality and good price.
- Good after-sale service. Solve your problems in time.
- Delivey in time.
IMPORTANT: WE SUPPLY THIS ITEM ONLY FOR REASEARCH PURPOSE.